Workshop – Journey Home

On the state park trail on Dec. 10, 2025.

After I finished the work table, I sorted stuff in the workshop. In other words, I filled the table with stuff thrown hodge-podge in every nook and cranny. This will be a long process, yet I am heartened by having another surface to use for this work. It is beginning with tools.

The table project was easy, with the radial arm saw and power drill being the main power tools. There were a few hand tools, but all of them are frequently used, and easy to find. That’s not the case with things tucked away in the workshop today.

I brought home a lot of tools when my father-in-law died. That was almost 30 years ago. I never really incorporated them into my workshop. As a result of this neglect, I don’t have visibility of every tool I own. When I’m starting a project I’m running blind. I hope to remedy that.

This tool visibility project began with my red Craftsman toolbox. It has three drawers and a compartment in the top. I took everything out of the drawers and rearranged it.

All the fixed wrenches went into their own tool box. I don’t use them as often as crescent wrenches and I’ll know where to find them when I need one. Crescent wrenches and pliers filled a drawer. One drawer has gripping tools. Most sizes of screwdrivers are on a pegboard, so the ones in the toolbox are either specialty drivers or extra. Screwdrivers get their own drawer, which isn’t enough space to accommodate them all. The solution to that will wait until I see what else I have. When I replaced some tools with others, the idea was to keep thosek most frequently used in the red toolbox.

There are also what I’ll call specialty toolboxes. One is full of drill bits of many kinds. I keep a separate drill bit holder on the bench so I can quickly find common sizes. There is a toolbox with woodworking tools. There are all kinds of them, although I am hardly a woodworker. One toolbox has a set of metric and imperial sockets. In the cabinet, there is another whole set of Craftsman sockets. This is just the beginning.

The main goal of this project is to gain visibility of what I have. I am tempted to acquire one of those tall movable toolboxes with many drawers. I hope that is a passing infatuation. For now, just knowing what I have should be enough to get started on new projects. The new table led to this, and who knows where the forking paths ahead will lead? Being aware of what tools I have is a good start.

I look forward to discovering where this goes.

Lumber to make a work table for the garage.

There was a time when I attended estate and farm auctions and bought things on the cheap for later projects. The years since then can be measured in decades. At a point in my life when I have to either do something with stuff, or otherwise dispose of it, I got out the top and legs of a table I bought for a buck at auction. It was time to make something. Since I rearranged the garage, I have space for a work table that is shorter than the custom-height workbench I made when we lived in Indiana.

I went through the woodpile and found planks to make an apron and five of rescued lumber to reinforce the top. I laid the materials out on this workbench made of sawhorses and thought about what I would do for a couple of weeks.

After looking at local hardware stores and large online retailers, I finally found a packet of figure 8 steel desk top fastener clips with screws. They are not commonly available. To make a recess in the apron for the fastener, I got a 20 millimeter forstner drill bit. $20.12 all in.

After 12 cuts on the radial arm saw, I was ready to assemble. I spent about three hours on the project before my attention began to wander. I am better at recognizing when that happens, so I knocked off for the day. If everything goes together as planned, it will take an hour or two to finish assembly.

After a few hours of furniture building I had to take a break.

I don’t plan to refinish the wood. Inside the garage it will be protected from the elements. I expect it to get scuffed up with heavy use, so what’s the point of a coat of paint or finish? The wood it’s made of has been around for a long time, based on the assembly techniques my predecessor used to build it.

Fingers crossed the final assembly passes muster and I can begin using the new table immediately. One never knows about these things until the work is done and the piece is in operation.

Here is the finished product in the garage.

Table made from a top, four legs and salvaged lumber.

It’s bigger than I thought, but I will adapt. No adjustments were needed.